Tufting machines | Second hand tufters for carpet and rugs up to 3999 mm width

1 pc. carpet tufting machine COBBLE (Ref. No. 6136092)
3300 mm working width, year of construction 2003, second-hand.
Loop pile, 1/8" gauge. On request with creel with 2016 positions and
with winder. Gauge in creel: 240 mm, vertical 260 mm.
The machine is practically new. 

1  pc. tufting machine COBBLE UTPA (Ref. No. 6125943)
1110 mm working width, year of construction 1992, second-hand
tufting width 43,75", 5/32" gauge, cut-loop
min. pile height .4724"
max. pile height .8661"
Including UTPA pattern attachment with PIV SLAT drive system.
With fabric shifter with rear pin roll drive, 16 1/2" CAM
and linear bearing shifter, complete with single deck
yarn creel for 280 ends.

3 pcs. tufting / rug repair guns - mending guns (Ref. No. 6145953)

1 pc. tufting machine COBBLE ICN (Ref. No. 6125945)
1000 mm working width, year of construction 1992
214 needles, 3/16" gauge, ICN cut pile
12 mm min. pile height, max. pile height 30 mm
with ICN pattern attachment with sliding needle plate,
tail picker, burling frame and re-roll device,
complete with yarn creel for 214 cones
Cobble Graphics Mender

1 pc. ICN tufting machine COBBLE ICN (Ref. No. 6125944)
1000 mm working width, year of construction 1987, second-hand
210 needles, tufting width 40 inches
gauge 3/16" ICN cut pile
pile height min. 3/8", max. 3/4"
with ICN pattern attachment with sliding needle plate,
16-1/2" shifter CAM

1 pc. tufting machine SINGER (Ref. No. 6125946)
600 mm working width, year of construction 1983, second-hand

1 pc. tufting machine EDGAR PICKERING LTD. BLACKBURN (Ref. No. 6125451)
1000 mm working width, year of construction: approx. 1971/1972
suitable for 1/8" and 1/10" gauge
cut pile, conversioned to module system
relatively low number of total working hours
previously used for pile height range of approx. 5/6 mm to 12/14 mm
with creel

1 pc. tufting machine PENDHILL (Ref. No. 6124645)
600 mm working width, year of construction ?, second-hand
cut pile, 5/32" gauge

1 pc. tufting machine SINGER I (Ref. No. 6124018)
1150 mm working width, year of construction 1973
1/10" cut pile
no gauge parts installed
no yarn guides
set of various spares available

1 pc. tufting machine COBBLE ST 80 (Ref. No. 6124019)
1150 mm working width, year of construction 1982
1/10" cross over cut pile
straight needle bar
1 PIV yarn feed, 24" cam
modular needles and loopers

1 pc. tufting machine COBBLE ST 85 (Ref. No. 6124020)
1150 mm working width, year of construction 1989
1/10" cross over loop pile
straight needle bar
1 PIV yarn feed - 1 PIV cloth feed
12" cam
modular needles and loopers

2 pcs. tufting machine COBBLE II (Ref. No. 6124021)
1150 mm working width, year of construction 1969
1/10" level loop
staggered needle bar
1 PIV yarn feed
modular needles and loopers

1 pc. tufting machine COBBLE (Ref. No. 6123044)
2900 mm working width, year of construction ?
3/8" gauge, cut-pile
including creel

1 pc. tufting machine CMC OMNI-GRAPH (Ref. No. 6122101)
24 " working width, year of construction 1995 - NEVER USED
special 1/8" gauge, 196 needles, cut pile
sample Omni-Graph tufting machine
equipped with two computer controlled sliding
needle bar attachments, yarn feed (front and rear)
CMC's Advanced cutting system II and complete
with 1/2 H.P. gear motor drive, as new, never used

Top of Page